DI-9M-08CEDAR電批扭力測試儀
| DI-9 series is most suitable for checking ａnd controlling the torque of Electric Screwdriver ａnd Torque Driver. |
| upgrade The main changed parts （1） In a display board, "measurement mode", a "measurement unit", "the maximum, the minimum, an average, etc.", etc. display. （2） Change of Measurement Unit Can be Performed N-m <=> kgf-cm <=>lbf-in Etc. （3） Setup of Various Numerical Values Can be Easy ａnd Can Carry Out Speedily. （4） Calculation of Maximum, Minimum, ａnd Average Became Intelligible. （5） The call of the saved data became easy. The output of data also became intelligible. （6） Fault charge protection. It is pilot-lamp lighting during charge. （7） Data Output is USB Form （B Type）. （8） Memory Data are 800 Affairs （9） Real-time Output is Every 1 / 180 Seconds. |
 |
  |
| The best for everyday check of an electric driver Wide measurement range （0 - 8000digit）, it corresponds to various set torques Can measure without inversion/ rolling-back work efficiently by OW joint （PAT.P）. |
| Specification | DI-9M-8 | DI-9M-08 | |
| Measuring range | 0.020-8 N?m | 2.0-800 mN?m | |
| 0.20～80 kgf?cm | 0.020～8 kgf?cm | ||
| 0.20～70 lbf?in | 0.020～7 lbf?in | ||
| Accuracy | ±0.5% （499 digit or less ±3digit） | ||
| Display | The 4 figures digital display of LCD | ||
| The measurement direction | CW-CCW （right ａnd left） | ||
| Zero return by one touch | Return to zero by pressing clear button. | ||
| Measurement Mode | Track , P-P（peak to peak） , P-D（Peak-Down） , C（Real-time Output） | ||
| High ａnd low limits judging function | High ａnd low value are measurement within the limits, ａnd can be set up. | ||
| Real-time Output | Load torque value is outputted every about1/ 180 second. | ||
| The Maximum, the minimum, ａnd the average value display | The maximum, the minimum, average value, ａnd the data number of 30 data are displayed.It saves to ten channels. | ||
| Data Output | ASCII format （baud rate 19200） | ||
| Auto power save | 10 minutes no use, automatically switch off. | ||
| Power supply | Ni-Cd chargeable battery 1.2V × 5cells 700mAh | ||
| Charging time | About 3hours | ||
| Continuous working time | About 12hours | ||
| clearance | It is a display clearance in set-up time. （0.1 - 3.0 sec） | ||
| Socket size | □ 20mm/ □9.5mm | ||
| Dimension / Weight | W:160×D:125×H:55 / About 1kg | ||
| Recommend buffer accessories | Measuring joint OW-20/OW-60 | Measuring joint OW-025/OW-10 | |
| Cube （with a 5th page screw hole） 20x20x20 （M2.6/M3/M4/M5/M6 Tap processing） | |||
| AC/DC adaptor | |||
| Exclusive receipt case | |||
| An inspection report, a proofreading certificate, a traceability system figure | |||
※Do not use for measurement of impact tool.Do not apply more than the specified torque.
| ● MEASURING JOINT OW series | |
 | Since our company developed the buffer with little influence of fricative, stable measurement could be performed Moreover ,it does not need to reverse-rotate at the time of measurement, ａnd work efficiency improved. |
| Specification | Type | ||||
| OW-025 | OW-10 | OW-20 | OW-60 | ||
| Measuring range N?m | 0.25 | 1 | 2 | 6 | |
| Mechanical life （times） | 10,000 | 8,000 | 5,000 | 5,000 | |
| Outer diameter size （mm） | Bit engagement part （screw part） | M2.6 cross recess screw | M3 cross recess screw | M4 cross recess screw | M6 cross recess screw |
| The standard screw is cross recess screw but they may be altered as necessary | |||||
| Outside diameter | φ28 | φ32 | φ32 | φ38 | |
| Height | 44 | 51 | 51 | 69 | |
| Ｉnstallation | 20square ×4（t） | ||||
DI-9M-8CEDAR電批扭力測試儀
| DI-9 series is most suitable for checking ａnd controlling the torque of Electric Screwdriver ａnd Torque Driver. |
| upgrade The main changed parts （1） In a display board, "measurement mode", a "measurement unit", "the maximum, the minimum, an average, etc.", etc. display. （2） Change of Measurement Unit Can be Performed N-m <=> kgf-cm <=>lbf-in Etc. （3） Setup of Various Numerical Values Can be Easy ａnd Can Carry Out Speedily. （4） Calculation of Maximum, Minimum, ａnd Average Became Intelligible. （5） The call of the saved data became easy. The output of data also became intelligible. （6） Fault charge protection. It is pilot-lamp lighting during charge. （7） Data Output is USB Form （B Type）. （8） Memory Data are 800 Affairs （9） Real-time Output is Every 1 / 180 Seconds. |
|
| |
| The best for everyday check of an electric driver Wide measurement range （0 - 8000digit）, it corresponds to various set torques Can measure without inversion/ rolling-back work efficiently by OW joint （PAT.P）. |
| Specification | DI-9M-8 | DI-9M-08 | |
| Measuring range | 0.020-8 N?m | 2.0-800 mN?m | |
| 0.20～80 kgf?cm | 0.020～8 kgf?cm | ||
| 0.20～70 lbf?in | 0.020～7 lbf?in | ||
| Accuracy | ±0.5% （499 digit or less ±3digit） | ||
| Display | The 4 figures digital display of LCD | ||
| The measurement direction | CW-CCW （right ａnd left） | ||
| Zero return by one touch | Return to zero by pressing clear button. | ||
| Measurement Mode | Track , P-P（peak to peak） , P-D（Peak-Down） , C（Real-time Output） | ||
| High ａnd low limits judging function | High ａnd low value are measurement within the limits, ａnd can be set up. | ||
| Real-time Output | Load torque value is outputted every about1/ 180 second. | ||
| The Maximum, the minimum, ａnd the average value display | The maximum, the minimum, average value, ａnd the data number of 30 data are displayed.It saves to ten channels. | ||
| Data Output | ASCII format （baud rate 19200） | ||
| Auto power save | 10 minutes no use, automatically switch off. | ||
| Power supply | Ni-Cd chargeable battery 1.2V × 5cells 700mAh | ||
| Charging time | About 3hours | ||
| Continuous working time | About 12hours | ||
| clearance | It is a display clearance in set-up time. （0.1 - 3.0 sec） | ||
| Socket size | □ 20mm/ □9.5mm | ||
| Dimension / Weight | W:160×D:125×H:55 / About 1kg | ||
| Recommend buffer accessories | Measuring joint OW-20/OW-60 | Measuring joint OW-025/OW-10 | |
| Cube （with a 5th page screw hole） 20x20x20 （M2.6/M3/M4/M5/M6 Tap processing） | |||
| AC/DC adaptor | |||
| Exclusive receipt case | |||
| An inspection report, a proofreading certificate, a traceability system figure | |||
※Do not use for measurement of impact tool.Do not apply more than the specified torque.
| ● MEASURING JOINT OW series | |
| Since our company developed the buffer with little influence of fricative, stable measurement could be performed Moreover ,it does not need to reverse-rotate at the time of measurement, ａnd work efficiency improved. |
| Specification | Type | ||||
| OW-025 | OW-10 | OW-20 | OW-60 | ||
| Measuring range N?m | 0.25 | 1 | 2 | 6 | |
| Mechanical life （times） | 10,000 | 8,000 | 5,000 | 5,000 | |
| Outer diameter size （mm） | Bit engagement part （screw part） | M2.6 cross recess screw | M3 cross recess screw | M4 cross recess screw | M6 cross recess screw |
| The standard screw is cross recess screw but they may be altered as necessary | |||||
| Outside diameter | φ28 | φ32 | φ32 | φ38 | |
| Height | 44 | 51 | 51 | 69 | |
| Ｉnstallation | 20square ×4（t） | ||||
DI-9M-08CEDAR電批扭力測試儀
| DI-9 series is most suitable for checking ａnd controlling the torque of Electric Screwdriver ａnd Torque Driver. |
| upgrade The main changed parts （1） In a display board, "measurement mode", a "measurement unit", "the maximum, the minimum, an average, etc.", etc. display. （2） Change of Measurement Unit Can be Performed N-m <=> kgf-cm <=>lbf-in Etc. （3） Setup of Various Numerical Values Can be Easy ａnd Can Carry Out Speedily. （4） Calculation of Maximum, Minimum, ａnd Average Became Intelligible. （5） The call of the saved data became easy. The output of data also became intelligible. （6） Fault charge protection. It is pilot-lamp lighting during charge. （7） Data Output is USB Form （B Type）. （8） Memory Data are 800 Affairs （9） Real-time Output is Every 1 / 180 Seconds. |
|
| |
| The best for everyday check of an electric driver Wide measurement range （0 - 8000digit）, it corresponds to various set torques Can measure without inversion/ rolling-back work efficiently by OW joint （PAT.P）. |
| Specification | DI-9M-8 | DI-9M-08 | |
| Measuring range | 0.020-8 N?m | 2.0-800 mN?m | |
| 0.20～80 kgf?cm | 0.020～8 kgf?cm | ||
| 0.20～70 lbf?in | 0.020～7 lbf?in | ||
| Accuracy | ±0.5% （499 digit or less ±3digit） | ||
| Display | The 4 figures digital display of LCD | ||
| The measurement direction | CW-CCW （right ａnd left） | ||
| Zero return by one touch | Return to zero by pressing clear button. | ||
| Measurement Mode | Track , P-P（peak to peak） , P-D（Peak-Down） , C（Real-time Output） | ||
| High ａnd low limits judging function | High ａnd low value are measurement within the limits, ａnd can be set up. | ||
| Real-time Output | Load torque value is outputted every about1/ 180 second. | ||
| The Maximum, the minimum, ａnd the average value display | The maximum, the minimum, average value, ａnd the data number of 30 data are displayed.It saves to ten channels. | ||
| Data Output | ASCII format （baud rate 19200） | ||
| Auto power save | 10 minutes no use, automatically switch off. | ||
| Power supply | Ni-Cd chargeable battery 1.2V × 5cells 700mAh | ||
| Charging time | About 3hours | ||
| Continuous working time | About 12hours | ||
| clearance | It is a display clearance in set-up time. （0.1 - 3.0 sec） | ||
| Socket size | □ 20mm/ □9.5mm | ||
| Dimension / Weight | W:160×D:125×H:55 / About 1kg | ||
| Recommend buffer accessories | Measuring joint OW-20/OW-60 | Measuring joint OW-025/OW-10 | |
| Cube （with a 5th page screw hole） 20x20x20 （M2.6/M3/M4/M5/M6 Tap processing） | |||
| AC/DC adaptor | |||
| Exclusive receipt case | |||
| An inspection report, a proofreading certificate, a traceability system figure | |||
※Do not use for measurement of impact tool.Do not apply more than the specified torque.
| ● MEASURING JOINT OW series | |
| Since our company developed the buffer with little influence of fricative, stable measurement could be performed Moreover ,it does not need to reverse-rotate at the time of measurement, ａnd work efficiency improved. |
| Specification | Type | ||||
| OW-025 | OW-10 | OW-20 | OW-60 | ||
| Measuring range N?m | 0.25 | 1 | 2 | 6 | |
| Mechanical life （times） | 10,000 | 8,000 | 5,000 | 5,000 | |
| Outer diameter size （mm） | Bit engagement part （screw part） | M2.6 cross recess screw | M3 cross recess screw | M4 cross recess screw | M6 cross recess screw |
| The standard screw is cross recess screw but they may be altered as necessary | |||||
| Outside diameter | φ28 | φ32 | φ32 | φ38 | |
| Height | 44 | 51 | 51 | 69 | |
| Ｉnstallation | 20square ×4（t） | ||||
DI-9M-8CEDAR電批扭力測試儀
| DI-9 series is most suitable for checking ａnd controlling the torque of Electric Screwdriver ａnd Torque Driver. |
| upgrade The main changed parts （1） In a display board, "measurement mode", a "measurement unit", "the maximum, the minimum, an average, etc.", etc. display. （2） Change of Measurement Unit Can be Performed N-m <=> kgf-cm <=>lbf-in Etc. （3） Setup of Various Numerical Values Can be Easy ａnd Can Carry Out Speedily. （4） Calculation of Maximum, Minimum, ａnd Average Became Intelligible. （5） The call of the saved data became easy. The output of data also became intelligible. （6） Fault charge protection. It is pilot-lamp lighting during charge. （7） Data Output is USB Form （B Type）. （8） Memory Data are 800 Affairs （9） Real-time Output is Every 1 / 180 Seconds. |
|
| |
| The best for everyday check of an electric driver Wide measurement range （0 - 8000digit）, it corresponds to various set torques Can measure without inversion/ rolling-back work efficiently by OW joint （PAT.P）. |
| Specification | DI-9M-8 | DI-9M-08 | |
| Measuring range | 0.020-8 N?m | 2.0-800 mN?m | |
| 0.20～80 kgf?cm | 0.020～8 kgf?cm | ||
| 0.20～70 lbf?in | 0.020～7 lbf?in | ||
| Accuracy | ±0.5% （499 digit or less ±3digit） | ||
| Display | The 4 figures digital display of LCD | ||
| The measurement direction | CW-CCW （right ａnd left） | ||
| Zero return by one touch | Return to zero by pressing clear button. | ||
| Measurement Mode | Track , P-P（peak to peak） , P-D（Peak-Down） , C（Real-time Output） | ||
| High ａnd low limits judging function | High ａnd low value are measurement within the limits, ａnd can be set up. | ||
| Real-time Output | Load torque value is outputted every about1/ 180 second. | ||
| The Maximum, the minimum, ａnd the average value display | The maximum, the minimum, average value, ａnd the data number of 30 data are displayed.It saves to ten channels. | ||
| Data Output | ASCII format （baud rate 19200） | ||
| Auto power save | 10 minutes no use, automatically switch off. | ||
| Power supply | Ni-Cd chargeable battery 1.2V × 5cells 700mAh | ||
| Charging time | About 3hours | ||
| Continuous working time | About 12hours | ||
| clearance | It is a display clearance in set-up time. （0.1 - 3.0 sec） | ||
| Socket size | □ 20mm/ □9.5mm | ||
| Dimension / Weight | W:160×D:125×H:55 / About 1kg | ||
| Recommend buffer accessories | Measuring joint OW-20/OW-60 | Measuring joint OW-025/OW-10 | |
| Cube （with a 5th page screw hole） 20x20x20 （M2.6/M3/M4/M5/M6 Tap processing） | |||
| AC/DC adaptor | |||
| Exclusive receipt case | |||
| An inspection report, a proofreading certificate, a traceability system figure | |||
※Do not use for measurement of impact tool.Do not apply more than the specified torque.
| ● MEASURING JOINT OW series | |
| Since our company developed the buffer with little influence of fricative, stable measurement could be performed Moreover ,it does not need to reverse-rotate at the time of measurement, ａnd work efficiency improved. |
| Specification | Type | ||||
| OW-025 | OW-10 | OW-20 | OW-60 | ||
| Measuring range N?m | 0.25 | 1 | 2 | 6 | |
| Mechanical life （times） | 10,000 | 8,000 | 5,000 | 5,000 | |
| Outer diameter size （mm） | Bit engagement part （screw part） | M2.6 cross recess screw | M3 cross recess screw | M4 cross recess screw | M6 cross recess screw |
| The standard screw is cross recess screw but they may be altered as necessary | |||||
| Outside diameter | φ28 | φ32 | φ32 | φ38 | |
| Height | 44 | 51 | 51 | 69 | |
| Ｉnstallation | 20square ×4（t） | ||||
DI-9M-08日本CEDAR電批扭力測試儀
| DI-9 series is most suitable for checking ａnd controlling the torque of Electric Screwdriver ａnd Torque Driver. |
| upgrade The main changed parts （1） In a display board, "measurement mode", a "measurement unit", "the maximum, the minimum, an average, etc.", etc. display. （2） Change of Measurement Unit Can be Performed N-m <=> kgf-cm <=>lbf-in Etc. （3） Setup of Various Numerical Values Can be Easy ａnd Can Carry Out Speedily. （4） Calculation of Maximum, Minimum, ａnd Average Became Intelligible. （5） The call of the saved data became easy. The output of data also became intelligible. （6） Fault charge protection. It is pilot-lamp lighting during charge. （7） Data Output is USB Form （B Type）. （8） Memory Data are 800 Affairs （9） Real-time Output is Every 1 / 180 Seconds. |
|
| |
| The best for everyday check of an electric driver Wide measurement range （0 - 8000digit）, it corresponds to various set torques Can measure without inversion/ rolling-back work efficiently by OW joint （PAT.P）. |
| Specification | DI-9M-8 | DI-9M-08 | |
| Measuring range | 0.020-8 N?m | 2.0-800 mN?m | |
| 0.20～80 kgf?cm | 0.020～8 kgf?cm | ||
| 0.20～70 lbf?in | 0.020～7 lbf?in | ||
| Accuracy | ±0.5% （499 digit or less ±3digit） | ||
| Display | The 4 figures digital display of LCD | ||
| The measurement direction | CW-CCW （right ａnd left） | ||
| Zero return by one touch | Return to zero by pressing clear button. | ||
| Measurement Mode | Track , P-P（peak to peak） , P-D（Peak-Down） , C（Real-time Output） | ||
| High ａnd low limits judging function | High ａnd low value are measurement within the limits, ａnd can be set up. | ||
| Real-time Output | Load torque value is outputted every about1/ 180 second. | ||
| The Maximum, the minimum, ａnd the average value display | The maximum, the minimum, average value, ａnd the data number of 30 data are displayed.It saves to ten channels. | ||
| Data Output | ASCII format （baud rate 19200） | ||
| Auto power save | 10 minutes no use, automatically switch off. | ||
| Power supply | Ni-Cd chargeable battery 1.2V × 5cells 700mAh | ||
| Charging time | About 3hours | ||
| Continuous working time | About 12hours | ||
| clearance | It is a display clearance in set-up time. （0.1 - 3.0 sec） | ||
| Socket size | □ 20mm/ □9.5mm | ||
| Dimension / Weight | W:160×D:125×H:55 / About 1kg | ||
| Recommend buffer accessories | Measuring joint OW-20/OW-60 | Measuring joint OW-025/OW-10 | |
| Cube （with a 5th page screw hole） 20x20x20 （M2.6/M3/M4/M5/M6 Tap processing） | |||
| AC/DC adaptor | |||
| Exclusive receipt case | |||
| An inspection report, a proofreading certificate, a traceability system figure | |||
※Do not use for measurement of impact tool.Do not apply more than the specified torque.
| ● MEASURING JOINT OW series | |
| Since our company developed the buffer with little influence of fricative, stable measurement could be performed Moreover ,it does not need to reverse-rotate at the time of measurement, ａnd work efficiency improved. |
| Specification | Type | ||||
| OW-025 | OW-10 | OW-20 | OW-60 | ||
| Measuring range N?m | 0.25 | 1 | 2 | 6 | |
| Mechanical life （times） | 10,000 | 8,000 | 5,000 | 5,000 | |
| Outer diameter size （mm） | Bit engagement part （screw part） | M2.6 cross recess screw | M3 cross recess screw | M4 cross recess screw | M6 cross recess screw |
| The standard screw is cross recess screw but they may be altered as necessary | |||||
| Outside diameter | φ28 | φ32 | φ32 | φ38 | |
| Height | 44 | 51 | 51 | 69 | |
| Ｉnstallation | 20square ×4（t） | ||||
DI-9M-08日本CEDAR電批扭力測試儀
| DI-9 series is most suitable for checking ａnd controlling the torque of Electric Screwdriver ａnd Torque Driver. |
| upgrade The main changed parts （1） In a display board, "measurement mode", a "measurement unit", "the maximum, the minimum, an average, etc.", etc. display. （2） Change of Measurement Unit Can be Performed N-m <=> kgf-cm <=>lbf-in Etc. （3） Setup of Various Numerical Values Can be Easy ａnd Can Carry Out Speedily. （4） Calculation of Maximum, Minimum, ａnd Average Became Intelligible. （5） The call of the saved data became easy. The output of data also became intelligible. （6） Fault charge protection. It is pilot-lamp lighting during charge. （7） Data Output is USB Form （B Type）. （8） Memory Data are 800 Affairs （9） Real-time Output is Every 1 / 180 Seconds. |
|
| |
| The best for everyday check of an electric driver Wide measurement range （0 - 8000digit）, it corresponds to various set torques Can measure without inversion/ rolling-back work efficiently by OW joint （PAT.P）. |
| Specification | DI-9M-8 | DI-9M-08 | |
| Measuring range | 0.020-8 N?m | 2.0-800 mN?m | |
| 0.20～80 kgf?cm | 0.020～8 kgf?cm | ||
| 0.20～70 lbf?in | 0.020～7 lbf?in | ||
| Accuracy | ±0.5% （499 digit or less ±3digit） | ||
| Display | The 4 figures digital display of LCD | ||
| The measurement direction | CW-CCW （right ａnd left） | ||
| Zero return by one touch | Return to zero by pressing clear button. | ||
| Measurement Mode | Track , P-P（peak to peak） , P-D（Peak-Down） , C（Real-time Output） | ||
| High ａnd low limits judging function | High ａnd low value are measurement within the limits, ａnd can be set up. | ||
| Real-time Output | Load torque value is outputted every about1/ 180 second. | ||
| The Maximum, the minimum, ａnd the average value display | The maximum, the minimum, average value, ａnd the data number of 30 data are displayed.It saves to ten channels. | ||
| Data Output | ASCII format （baud rate 19200） | ||
| Auto power save | 10 minutes no use, automatically switch off. | ||
| Power supply | Ni-Cd chargeable battery 1.2V × 5cells 700mAh | ||
| Charging time | About 3hours | ||
| Continuous working time | About 12hours | ||
| clearance | It is a display clearance in set-up time. （0.1 - 3.0 sec） | ||
| Socket size | □ 20mm/ □9.5mm | ||
| Dimension / Weight | W:160×D:125×H:55 / About 1kg | ||
| Recommend buffer accessories | Measuring joint OW-20/OW-60 | Measuring joint OW-025/OW-10 | |
| Cube （with a 5th page screw hole） 20x20x20 （M2.6/M3/M4/M5/M6 Tap processing） | |||
| AC/DC adaptor | |||
| Exclusive receipt case | |||
| An inspection report, a proofreading certificate, a traceability system figure | |||
※Do not use for measurement of impact tool.Do not apply more than the specified torque.
| ● MEASURING JOINT OW series | |
| Since our company developed the buffer with little influence of fricative, stable measurement could be performed Moreover ,it does not need to reverse-rotate at the time of measurement, ａnd work efficiency improved. |
| Specification | Type | ||||
| OW-025 | OW-10 | OW-20 | OW-60 | ||
| Measuring range N?m | 0.25 | 1 | 2 | 6 | |
| Mechanical life （times） | 10,000 | 8,000 | 5,000 | 5,000 | |
| Outer diameter size （mm） | Bit engagement part （screw part） | M2.6 cross recess screw | M3 cross recess screw | M4 cross recess screw | M6 cross recess screw |
| The standard screw is cross recess screw but they may be altered as necessary | |||||
| Outside diameter | φ28 | φ32 | φ32 | φ38 | |
| Height | 44 | 51 | 51 | 69 | |
| Ｉnstallation | 20square ×4（t） | ||||
DI-9M-8日本CEDAR電批扭力測試儀
| DI-9 series is most suitable for checking ａnd controlling the torque of Electric Screwdriver ａnd Torque Driver. |
| upgrade The main changed parts （1） In a display board, "measurement mode", a "measurement unit", "the maximum, the minimum, an average, etc.", etc. display. （2） Change of Measurement Unit Can be Performed N-m <=> kgf-cm <=>lbf-in Etc. （3） Setup of Various Numerical Values Can be Easy ａnd Can Carry Out Speedily. （4） Calculation of Maximum, Minimum, ａnd Average Became Intelligible. （5） The call of the saved data became easy. The output of data also became intelligible. （6） Fault charge protection. It is pilot-lamp lighting during charge. （7） Data Output is USB Form （B Type）. （8） Memory Data are 800 Affairs （9） Real-time Output is Every 1 / 180 Seconds. |
|
| |
| The best for everyday check of an electric driver Wide measurement range （0 - 8000digit）, it corresponds to various set torques Can measure without inversion/ rolling-back work efficiently by OW joint （PAT.P）. |
| Specification | DI-9M-8 | DI-9M-08 | |
| Measuring range | 0.020-8 N?m | 2.0-800 mN?m | |
| 0.20～80 kgf?cm | 0.020～8 kgf?cm | ||
| 0.20～70 lbf?in | 0.020～7 lbf?in | ||
| Accuracy | ±0.5% （499 digit or less ±3digit） | ||
| Display | The 4 figures digital display of LCD | ||
| The measurement direction | CW-CCW （right ａnd left） | ||
| Zero return by one touch | Return to zero by pressing clear button. | ||
| Measurement Mode | Track , P-P（peak to peak） , P-D（Peak-Down） , C（Real-time Output） | ||
| High ａnd low limits judging function | High ａnd low value are measurement within the limits, ａnd can be set up. | ||
| Real-time Output | Load torque value is outputted every about1/ 180 second. | ||
| The Maximum, the minimum, ａnd the average value display | The maximum, the minimum, average value, ａnd the data number of 30 data are displayed.It saves to ten channels. | ||
| Data Output | ASCII format （baud rate 19200） | ||
| Auto power save | 10 minutes no use, automatically switch off. | ||
| Power supply | Ni-Cd chargeable battery 1.2V × 5cells 700mAh | ||
| Charging time | About 3hours | ||
| Continuous working time | About 12hours | ||
| clearance | It is a display clearance in set-up time. （0.1 - 3.0 sec） | ||
| Socket size | □ 20mm/ □9.5mm | ||
| Dimension / Weight | W:160×D:125×H:55 / About 1kg | ||
| Recommend buffer accessories | Measuring joint OW-20/OW-60 | Measuring joint OW-025/OW-10 | |
| Cube （with a 5th page screw hole） 20x20x20 （M2.6/M3/M4/M5/M6 Tap processing） | |||
| AC/DC adaptor | |||
| Exclusive receipt case | |||
| An inspection report, a proofreading certificate, a traceability system figure | |||
※Do not use for measurement of impact tool.Do not apply more than the specified torque.
| ● MEASURING JOINT OW series | |
| Since our company developed the buffer with little influence of fricative, stable measurement could be performed Moreover ,it does not need to reverse-rotate at the time of measurement, ａnd work efficiency improved. |
| Specification | Type | ||||
| OW-025 | OW-10 | OW-20 | OW-60 | ||
| Measuring range N?m | 0.25 | 1 | 2 | 6 | |
| Mechanical life （times） | 10,000 | 8,000 | 5,000 | 5,000 | |
| Outer diameter size （mm） | Bit engagement part （screw part） | M2.6 cross recess screw | M3 cross recess screw | M4 cross recess screw | M6 cross recess screw |
| The standard screw is cross recess screw but they may be altered as necessary | |||||
| Outside diameter | φ28 | φ32 | φ32 | φ38 | |
| Height | 44 | 51 | 51 | 69 | |
| Ｉnstallation | 20square ×4（t） | ||||
DI-9M-8日本CEDAR電批扭力測試儀
| DI-9 series is most suitable for checking ａnd controlling the torque of Electric Screwdriver ａnd Torque Driver. |
| upgrade The main changed parts （1） In a display board, "measurement mode", a "measurement unit", "the maximum, the minimum, an average, etc.", etc. display. （2） Change of Measurement Unit Can be Performed N-m <=> kgf-cm <=>lbf-in Etc. （3） Setup of Various Numerical Values Can be Easy ａnd Can Carry Out Speedily. （4） Calculation of Maximum, Minimum, ａnd Average Became Intelligible. （5） The call of the saved data became easy. The output of data also became intelligible. （6） Fault charge protection. It is pilot-lamp lighting during charge. （7） Data Output is USB Form （B Type）. （8） Memory Data are 800 Affairs （9） Real-time Output is Every 1 / 180 Seconds. |
|
| |
| The best for everyday check of an electric driver Wide measurement range （0 - 8000digit）, it corresponds to various set torques Can measure without inversion/ rolling-back work efficiently by OW joint （PAT.P）. |
| Specification | DI-9M-8 | DI-9M-08 | |
| Measuring range | 0.020-8 N?m | 2.0-800 mN?m | |
| 0.20～80 kgf?cm | 0.020～8 kgf?cm | ||
| 0.20～70 lbf?in | 0.020～7 lbf?in | ||
| Accuracy | ±0.5% （499 digit or less ±3digit） | ||
| Display | The 4 figures digital display of LCD | ||
| The measurement direction | CW-CCW （right ａnd left） | ||
| Zero return by one touch | Return to zero by pressing clear button. | ||
| Measurement Mode | Track , P-P（peak to peak） , P-D（Peak-Down） , C（Real-time Output） | ||
| High ａnd low limits judging function | High ａnd low value are measurement within the limits, ａnd can be set up. | ||
| Real-time Output | Load torque value is outputted every about1/ 180 second. | ||
| The Maximum, the minimum, ａnd the average value display | The maximum, the minimum, average value, ａnd the data number of 30 data are displayed.It saves to ten channels. | ||
| Data Output | ASCII format （baud rate 19200） | ||
| Auto power save | 10 minutes no use, automatically switch off. | ||
| Power supply | Ni-Cd chargeable battery 1.2V × 5cells 700mAh | ||
| Charging time | About 3hours | ||
| Continuous working time | About 12hours | ||
| clearance | It is a display clearance in set-up time. （0.1 - 3.0 sec） | ||
| Socket size | □ 20mm/ □9.5mm | ||
| Dimension / Weight | W:160×D:125×H:55 / About 1kg | ||
| Recommend buffer accessories | Measuring joint OW-20/OW-60 | Measuring joint OW-025/OW-10 | |
| Cube （with a 5th page screw hole） 20x20x20 （M2.6/M3/M4/M5/M6 Tap processing） | |||
| AC/DC adaptor | |||
| Exclusive receipt case | |||
| An inspection report, a proofreading certificate, a traceability system figure | |||
※Do not use for measurement of impact tool.Do not apply more than the specified torque.
| ● MEASURING JOINT OW series | |
| Since our company developed the buffer with little influence of fricative, stable measurement could be performed Moreover ,it does not need to reverse-rotate at the time of measurement, ａnd work efficiency improved. |
| Specification | Type | ||||
| OW-025 | OW-10 | OW-20 | OW-60 | ||
| Measuring range N?m | 0.25 | 1 | 2 | 6 | |
| Mechanical life （times） | 10,000 | 8,000 | 5,000 | 5,000 | |
| Outer diameter size （mm） | Bit engagement part （screw part） | M2.6 cross recess screw | M3 cross recess screw | M4 cross recess screw | M6 cross recess screw |
| The standard screw is cross recess screw but they may be altered as necessary | |||||
| Outside diameter | φ28 | φ32 | φ32 | φ38 | |
| Height | 44 | 51 | 51 | 69 | |
| Ｉnstallation | 20square ×4（t） | ||||
最新產品
- 南京熱熔道路標線 道路劃線施工 2025/12/4 22:14:09
- 德國boxer液體隔膜泵 2025/12/4 21:33:16
- 德國Tempris冷凍干燥機用射頻天線 2025/12/4 21:30:16
- 葡萄牙VALSTEAM ADCA蒸汽疏水閥 2025/12/4 21:26:45
- 瑞典PRECIMETER移動式液位傳感器 2025/12/4 21:23:49
- 德國zipatec線性模塊直線電機線性模塊 2025/12/4 21:21:35
- 德國hawo封口機 2025/12/4 21:18:55
- 德國KACO密封柴油燃油泵徑向軸密封件 2025/12/4 21:15:14
- THERMO SENSOR熱電偶1133-11-2283 2025/12/4 21:14:46
- 法國PLASTIFORM復制膠泥 2025/12/4 21:12:30
- 德國westring唇形密封圈 2025/12/4 21:09:49
- 英國Porvair膠囊過濾器 2025/12/4 21:06:14
- Robatech噴頭SX DIAMOND 2025/12/4 21:01:12
- Seneca網關Z-KEY-MBUS 2025/12/4 20:22:01
- JBZC6311電渦流傳感器（軸位移） 2025/12/4 19:23:54
- JBZC6701磁電式轉速傳感器 2025/12/4 19:18:48
- Q-80Z鉅惠儀器自動金相切割機Q-80Z 2025/12/4 19:17:42
- JBZC6702霍爾轉速傳感器 2025/12/4 19:13:15
- Q-2A鉅惠臺式手動Φ55mm金相試樣切割機Q-2A 2025/12/4 19:12:21
- JBZC6401壓電式振動傳感器 2025/12/4 19:07:58
- Q-2鉅惠臺式Φ35mm手動金相試樣切割機Q-2 2025/12/4 19:07:46
- HQGZ-350SY鉅惠儀器金相試樣自動切割機HQGZ-350SY 2025/12/4 19:00:42
- MENCOM有接頭電纜MCVP-19FP-5M-R，更多產品請咨詢希而科！ 2025/12/4 18:55:11
- HQG-200D鉅惠儀器高速精密切割機HQG-200D 2025/12/4 18:54:04
- HQG-200B鉅惠儀器低速精密切割機HQG-200B 2025/12/4 18:46:30
- HQG-100D鉅惠儀器低速精密切割機HQG-100D 2025/12/4 18:38:27
- HQG-80鉅惠儀器金相試樣切割機HQG-80 2025/12/4 18:31:23
- Q-100Z鉅惠儀器金相試樣自動切割機Q-100Z 2025/12/4 18:25:25
- 鉅惠儀器金相試樣自動切割機HQGZ-300SY 2025/12/4 18:18:46
- 深圳社保外包人事代理，人力資源服務勞務派遣 2025/12/4 18:02:27